Archive for the ‘HPE Systems’ Category

HPE MSA 2062 Gen6 Storage Array – QuickSpecs

Freitag, Oktober 15th, 2021

HPE MSA 2062 Gen6 Storage Array – is here

Freitag, Oktober 15th, 2021

Oracle – hat den langjährigen Streit um den Itanium Support gegen HPE verloren und muss dem Konkurrenten nun über $ 3 Milliarden Schadensersatz zahlen

Samstag, Oktober 2nd, 2021

HPE ProLiant DL380 Gen10 Plus Server – QuickSpecs

Dienstag, Juni 8th, 2021

   HPE ProLiant DL380 Gen10 Plus Server – QuickSpecs

HPE ProLiant DL380 Gen10 Plus Server – unterstützt die skalierbaren Intel Xeon Prozessoren der 3. Generation

Dienstag, Juni 8th, 2021

HPE ProLiant DL380 Gen10 Server – QuickSpecs V40 05 October 2020

Sonntag, Oktober 25th, 2020

   HPE ProLiant DL380 Gen10 Server – QuickSpecs

 

HPE ProLiant DL380 Gen9 Server – the HPE Dynamic Smart Array B140i Controller is not compliant with certain HPE Gen9 platforms running VMware ESXi 7.0

Samstag, Oktober 17th, 2020

The HPE Dynamic Smart Array B140i Controller will not be listed on the compliance recipe list for VMware ESXi 7.0 because it is not supported on certain HPE Gen9 platforms running VMware ESXi 7.0

HPE Primera – now is the time for intelligent storage that manages itself for every mission-critical app of today and tomorrow

Freitag, Juni 12th, 2020

HPE MSA ‚Health Check‘ – for best practice, unhealthy components and firmware

Dienstag, Mai 19th, 2020

HPE Server der ProLiant Gen9 Serie – hier kann es zu einem unerwarteten Zurücksetzen oder Herunterfahren kommen

Donnerstag, Mai 14th, 2020

HPE Server der ProLiant Gen9 Serie –hier kann es zu einem unerwarteten Zurücksetzen oder Herunterfahren kommen

HPE ProLiant DL385 Gen10 Plus – with AMD EPYC Processors

Dienstag, Mai 5th, 2020

HPE Smart Array SR Gen10 Controllers – Firmware Update required to Prevent Potential Data Inconsistency on Select RAID Configurations with Smart Array Gen10 Firmware Version 1.98 through 2.62

Dienstag, Mai 5th, 2020

HPE Smart Array SR Gen10 Controller Firmware Version 2.65 (or later) – provided in the Resolution section of this document is required to prevent a potential data inconsistency on select RAID configurations with Smart Array Gen10 Firmware Version 1.98 through 2.62 based on the following scenarios. HPE strongly recommends performing this upgrade at the customer’s earliest opportunity per the „Action Required“ in the table located in the Resolution section. Neglecting to perform the recommended resolution could result in potential subsequent errors and potential data inconsistency

HPE Primera – take a close look and see what life is like for data inside

Sonntag, April 19th, 2020

HPE SAS Solid State Drives – Critical Firmware Upgrade Required for Certain HPE SAS Solid State Drive Models to Prevent Drive Failure at 40,000 Hours of Operation

Mittwoch, März 25th, 2020

HPE SAS Solid State Drives – after the SSD failure occurs neither the SSD nor the data can be recovered. In addition SSDs which were put into service at the same time will likely fail nearly simultaneously. Restoration of data from backup will be required in non-fault tolerance modes (e.g., RAID 0) and in fault tolerance RAID mode if more drives fail than what is supported by the fault tolerance RAID mode logical drive

 

SSD Issue Detection Scripts

HPE Container Strategy – transformation challenges

Sonntag, März 8th, 2020